How to Turn a Soda Can into a Spring Flower Brooch

Pin It

Diane Gilleland, contributor

154 users recommend

An ordinary soda can provides pretty graphics and shiny metal. They combine to form a bold and beautiful flower brooch.

Diane Gilleland

The beads and wire you see here not only decorate the flower's center, but they also cleverly hold the layers of metal together.

Diane Gilleland

Soda cans are made of very thin metal, so you can easily cut them with a strong pair of scissors.

Diane Gilleland

An ordinary soda can provides pretty graphics and shiny metal. They combine to form a bold and beautiful flower brooch.

Photo: Diane Gilleland

Add Comment
Print

This design is pretty forgiving, by the way. If you're an astute observer, you may have noticed that I started out with six sets of holes in the center of my flower, intending to install six beads. But I decided that I liked the look of five beads. No worries— the beads have covered up that last set of holes, so no one will know. Well, except you, of course.

With all the beads wired on, twist the two remaining ends of the wire together and trim them.

When you're done adding beads, just twist the two ends of the wire together at the back, and trim them to about 1/2 inch. Bend the twisted wire flat against the back of the flower.

Apply E-6000 to the back of the flower.

Apply a generous dollop of E-6000 over the back of the wires. Cut a small circle from a scrap of soda can and press this over the glue.

Cover the wire with a leftover piece of the can, then glue on a pin back.

Glue a pin back over the circle, and let this sit for a couple of hours while the glue cures.

You can use these flowers for more than jewelry, of course. Imagine them lining a picture frame or the edges of a round mirror. Imagine them decorating a lampshade. Imagine them as package toppers or glued around the base of a pillar candle.

View 1 member project gallery

My Creations
flowergirl19

Add Comment Print

How Spray-Paint Stencils Saved a Tablecloth  

Back to List

How to Make an Eco-Friendly Quilted Tote Bag

Comments (22)

MarshallAngelique writes: One admits that humen's life seems to be not very cheap, nevertheless some people need cash for various issues and not every one gets big sums cash. Therefore to get some business loans and student loan would be a correct solution.
Posted: 1:28 pm on September 16th

melinda54 writes: these are great , what if you folded the edges under and then
backed with craft foam,that would take care of the sharp edges
Posted: 5:48 pm on July 15th

lindaisrael writes: Diane,

I found this entry when I was looking for an idea on crimping metal, as I have been cutting up cans for a while and had a new idea I wanted to try... When I landed on the site and saw that it was you I laughed and thought, well I better leave a comment! Great job on the photos and instructions. I use a sharp pair of Fiskers to cut my cans. I basically stab the can and then start cutting. Another tip, I picked up some gloves from Harbor Freight, they are made by Western Safety (black nylon with nitrile palms), these are thin enough that I can feel the can but protective enough that I don't get cuts from the can.

Anyway I'm so glad that I have found your creative spots on the web, you are appreciated!
Posted: 5:24 pm on January 18th

nicart writes: I stuck the cut cans on a sheet of sticky foam from the craft store & cut the shapes with the foam backing. It helps flatten out the cans & keeps the edges from being sharp. I also use a die cutter to cut shapes from foam-backed aluminum cans & it's not sharp.
Posted: 12:04 am on May 20th

gossamer_wings writes: I have used my sizzlet machine to cut old soda cans....and you could use alcohol ink or sharpies to color the cans as well

I am going to try this in one of my altered books.....

Melissa
Posted: 7:09 pm on February 8th

foxysandora writes: What a fantastic idea. I'm a newbie to this site, actually to any site for that matter. I'm so EXCITED! I love to learn ways of using what is around us to make every day things. I was saving bottoms and tops of can goods for awhile, but couldn't come up with a way to use them. I had enough to build a small house ;). Now that I have seen your soda can brooch my mind is going in all kinds of directions on how to make the edges really safe. I'll get back to you if I come up with any thing. I like the crochet idea but I would like something a bit more solid. Great work, you are so creative, wow!!!
Posted: 2:19 pm on August 1st

flowergirl19 writes: I've made about 20 now, and I am still making them! =]
I used almost all of the soda can's metal and I made a pin with one big flower, and two smaller ones. I also put a bigger bead in the middle of the 6 beads. Thank you!
Posted: 4:45 pm on June 23rd

flowergirl19 writes: I've made 4 of them, and I love doing it! They're not too sharp on the edges, and I put one on my purse as a decoration. The E-6000 glue is a little smelly, though.

Posted: 12:40 pm on May 16th

javadiva writes: I recently discovered using pop cans for crafts and I've stamped on the silver part and I've used different shape punches like butterflies and scallops. The punches get sharpened every time.
Posted: 1:42 pm on May 4th

Sweet_Dee writes: Very creative...could prob. make a rose out of a coke can.
Posted: 3:52 am on May 4th

Sister_Diane writes: mrsg3, thank you for all the great variation ideas!

eveh, I love the crochet concept - will have to play around with that.

ArtfulAileen, thanks so much for the rusting tips!



Posted: 8:24 am on May 3rd

mrsg3 writes: I liked eveh's idea but I don't crochet. I just did a test with poking holes and doing a whip stitch over the edge with different fibers and the heavier ones worked best, crochet cotton, heavy yarn, waxed linen cord. Also tried with strung seed beads on wire which worked pretty well too. So with my idea for covering the edges with stained glass foiling tape and theses new ideas spured on by eveh, I think we can all give it a try and feel safe!
Posted: 10:46 pm on May 2nd

eveh writes: I'll bet you could poke holes around the flower petals and crochet a soft edge.
Posted: 4:45 pm on May 2nd

tototwo2 writes: How do you get the edges of the medal to not be sharp and keep from getting cut on your final product?
Posted: 2:49 pm on May 2nd

mrsg3 writes: Hi all.
I tried this but used stained glass copper tape on the edges and burnished them down. It comes in several widths and finishes. Also there a not enugh attractive cans around here so I use any can and then use model paint for metal items to paint on my pieces. This opens up for lots of possibilities including different patinas on the foil tape.

Enjoy the possibilities! Marie
Posted: 12:49 pm on May 2nd

marylucille writes: A lady visited and demonstrated this to our garden club back in the fifties. It was rejected by all members as too dangerous to be useful. I still think the same thing.
Posted: 12:37 pm on May 2nd

ArtfulAileen writes: Unfortunately you can't rust aluminum but you can use Modern Options and paint on iron paint and then add the patina solution over that and it will rust and look like it had sat out in the weather and rusted. Here's a link to the product:
http://www.modernoptions.com/

Hope this helps,

Aileen~
Outside The Margins
http://www.outsidethemargins.com/
My Blog
http://aileensmusings.blogspot.com/
Posted: 12:28 pm on May 2nd

Char50 writes: I agree that this looks too dangerous to wear...if a small child should run up to hug you they could get cut by the edges or poked in the eye by the stamens. It would be beautiful if framed, though.
Posted: 10:15 am on May 1st

Sister_Diane writes: SantaClaus - that's an intriguing question. There are paints that create a rusted-look finish, such as:

http://www.paint-store.net/store/home.php?cat=2

And here's a natural method that apparently works for tin, so it might be worth a try on aluminum:

http://www.the-artistic-garden.com/rusted-metal-faux-finish.html

I haven't tried either of these myself, so if you do, I'd love to hear how it went.
Posted: 11:24 pm on April 27th

SantaClaus writes: I'm trying to figure out how I could use the flower with a stem to put in a vase & get it "rusty" looking. Any thoughts on this would be appreciated!
Posted: 6:19 am on April 27th

Sister_Diane writes: Maureclaire, I'd say that this design is safe as a brooch, provided that you take some precaution with the edges. The steel wool step is very helpful. I've worn mine several times without incident, but I'd certainly agree that I'd keep it away from small children, just to be extra-safe.

Another interesting way to use the soda can metal is to cut it in simpler shapes like squares and rectangles, and then wrap some metal tape around those edges to soften them.
Posted: 12:07 am on April 27th

Maureclaire writes:
Soooo cute; and, beyond creative... but, isn't it a bit dangerous as a brooch ? Maybe better on a frame that's just going to be up on a the wall where no one is going to touch it.. know what I mean ? Or does the steel wool take care of that ?
Posted: 12:09 pm on April 25th

You must be logged in to post comments. Click here to login.